Leading 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Leading 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Do not ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Instance 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist needs to first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal needs to be issued first. High-speed doglegs are banned. High-speed sharp turns will cause the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is prohibited to brake instantly while driving with lots unless there are special situations.
6. When the forklift is running, it needs to follow the website traffic rules in the manufacturing facility and have to keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest placement that does not prevent the driving, and the gantry needs to be properly tilted back. The load will not be elevated other than when piling or packing. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to stand on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork suggestion need to not touch other products or things. The load must be maintained with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to select, transform pallet dump.

Leaving .
1. It is Electric Forklift Truck for Warehouse restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo must Stand-on Electric Pallet Stacker be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to stop the propensity of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844